|
| Catalogue |
Our latest catalogue will be sent to you, quickly and without any cost after your online request.
|
|
|
|
|
Shaft ladder and covers
|
 Download our catalogue about shaft ladder and covers here.
Climbing handle, for shafts and cellars
Climbing handle with steel or stainless steel (V4A) core, casing exists of smooth, jointless polyethylene (HDPE).
Equipped with anti-skid surface. Black colour when steel core, orange colour when stainless steel core. Complies
with DIN V 19 555 and DIN 1264 part 2.
Alcove ladder
Made of stainless steel .4301 (V2A) . To be anchored in concrete. Finished in stainless steel (V2A)
with welded rungs (U-profile). Complete with drilling holes for securing.
W x H x D = 200 x 220 x 170 mm
For industrial application. Galvanized or stainless steel and acid proof V4A (1.471), approved in accordance with the standards VBG 74/ GUV 6.4 of safety institutions.
Shaft ladder, galvanised steel
Internal rung width 300 mm 1400 mm. Stile size 50 x 20 mm, profiled perforated anti-skid rungs.
Shaft ladder stainless steel, with special coating. Internal rung width 300 mm I 400o
mm. Stile size 50 x 20 mm, profiled perforated anti-skid rungs.
Shaft ladder of GRP (glass fibre reinforced plastic)
Internal rung width 300 mm I 400 mmo. Stile size 50 x 20 mm, corrugated rungs.
Holding bar with two handles for shaft ladder, mobile
Stainless steel V4A (1.4571) coated. Quick and simple mounting in any shaft. Cost saving, only the sleeve is and
stays fixed in the shaft. Insulated handles protect against the cold and provide a good grip. Simple assembly, put the
bar into the sleeve and secure by turning.
Insert sleeve
Stainless steel V4A (1.4571), coated or galvanised steel. Suitable for the holding bar mentioned above.
Holding bar with one handle for shaft ladder, with wall frame
Stainless steel V4A (1.4571), coated or galvanised steel. With insert sleeve to be mounted on wall. Can be lowered after use.
Holding bar with one handle for shaft ladder, with insert sleeve
Stainless steel V4A (1.4571), coated or galvanised steel. With stile attachment. Can be lowered after use. Suitable for stile size 50 x 20 to 60 x 25 mm
Holding bar for shaft ladder, double
Stainless steel V4A (1.4571), coated. Double bar for even more security. Can be lowered after use. Is delivered completely with assembly set. Suitable for stile size 50 x 20 mm. For ladder width 340 and 440 mm.
Shaft cover, square
Stainless steel 1.4301, pickled and passivated and of course sealed. The cover is 2 mm thick stainless steel metal plate and in the middle
a small elevation for the draining of water. The bottom side of the cover has reinforcing frames and a safe handle. With self-locking
mechanism and manual release. A rustproof steel gas-pressurised spring makes the opening easier. Hinges on the inside, cover has
exchangeable seal. Operator key is included.
Also available 25mm hard foam insulation CFC free, equipped with 1 mm metal sheet for protection against liquid and damaging.
Shaft cover, round
The same the square shaft cover, above. The cover is equipped with robust hinge on assembly frame.
Shaft cover, square with ventilation chimney
Stainless steel 1.4301, pickled and passivated. The cover is 2 mm thick stainless steel metal plate and in the middle a small elevation for
the draining of water. With approx. 250mm high ventilation chimney, that has stainless steel dust and insect gauze. The bottom side of
the cover has reinforcing frames and a safe handle. With self-locking mechanism and manual release. A rustproof steel gas-pressurised
spring makes the opening easier. Hinges on the inside, cover has exchangeable seal. Operator key is included.
Also available 25mm hard foam insulation CFC free, equipped with 1 mm metal sheet for protection against intrusion of fluids and
against damaging.
Shaft cover, round with ventilation chimney
As described above. The cover is equipped with robust hinge on assembly frame.
Shaft cover, various surfaces
Gas and water proof, attachment by means of screw in each corner. Cone shaped, which
makes shifting easier. Equipped with armoured concrete and handles.
Load: test force 125 KN (= 12,5 t) after cover through has been filled with B 25 concrete
Depth cover: 80 mm
Height: 105 mm
Other load classifications and measurements on request.
Shaft cover, with steel plate
Gas and water proof, attachment by means of screw in each in each corner. Steel plate with anti-skid profile.
Load: 10 KN (= 1 t)
Height: 63 mm
Other load classifications and measurements on request.
Shaft cover
Corrosion-resistant steel 1.4301, galvanised and can be driven over. Stabile framework with exchangeable seal. Cover is made of bulb plate, with galvanised hinge and 2 threaded couplings. Handle for opening OF Opening handle, corrosion-resistant steel gas pressure spring, splashproof and flat insertion to maintain your flat floor surface.
|
|
|
